|
|
DIG1
0.52 kg
Spec Sheet
|
Digital Timer Unit
The DIG1 is a 12-27.2 Volt universal timer module that will perform the following tasks.
¤ Energise on start and then drop out after the selected time has expired.
¤ Energise on start and then drop out after timed out then repeat cycle.
¤ Delayed on start for a set time and then energises, after the time set has expired the relay will de-energise, the timer will then repeat the cycle until the input start is restored.
¤ Delayed on start, and then the relay energises and stays activated until input start is restored
|
|
|
Double Knock Module/DK
0.32 kg
Spec Sheet
|
Double Knock Module
This module is designed to activate a clean set of relay contacts when the closed input loop is activated twice within the time set by the on-board jumpers, or by being left open longer than the designated time. The module can be set to auto reset or to latch using the red latch/non-latch jumper.
|
|
|
Guard Timer
0 kg
|
Guard Timer
Closed circuit reset will initiate the timer for the set duration - between 6 and 135 minutes (2h 15m). If the time is not reset in this duration the unit will go into alarm condition, via a buzzer and LED output. After a second preset time the unit will change relay state if reset has not been initiated.
|
|
|
Kentim2
0 kg
|
12 Volt DC time clock
DISCONTINUED - Servicing still available.
|
|
|
K Trade 1
0.138 kg
Spec Sheet
|
Trade timer
This unit is fully programmed for auto change summer/winter daylight saving according to MEZ, GB and USA. The single channel digital time module with clean changeover 5 amp on-board relay has 28 memory locations, with free block formation and separate programming of switch ON and OFF times.
|
|
|
MT1
0.59 kg
|
12/24 Volt DC multi-timer
Unit has double clean changeover contacts and LED indication for supply and timer running. LED and buzzer outputs are activated on start time release. Start time by either open circuit loop, closed loop or pulsed AC or DC. Option for latched start or auto-reset.
|
|
|
PUL1/DK
0.32 kg
Spec Sheet
|
Pulse Delay Module
The PUL1 Pulse Delay Module is a small compact PCB that will energise a set of 1A relay contacts when the NC loop is opened. When the loop has been opened a timer starts and the relay will remain energised until the time has expired at which point it will de-energise. The timer is software driven and is available in 1-8 5-40 10-80 seconds, see the spec sheet for full details.
The timer can also be triggered from a -VE input or by leaving the loop open and applying power to the PCB and the timer will start on power up.
|
|
|
PUL4/DK
0.32 kg
Spec Sheet
|
Relay Pulse Module
The RP Module is a compact control PCB that will activate when the NC input is closed with a push to close button or momentary input. When this occurs the RP Module will energise the relay, at this point a timer will hold the relay active for an adjustable time delay and hold this state until the preset time has expired. The relay will then de-energise for another adjustable preset time until it will again energise the for the preset time. The module will continue to do this until the unit has completed 5 cycles when it will stop.
|
|
|
Flip Flop / Timer/DK
0 kg
Spec Sheet
|
Flip Flop Timer Module
The FF/Timer Module is a compact control PCB which can be used in a number of applications where a single push on / push off button is required. The module is also a timer, when the loop is opened the relay operates and will stay energised, when the loop is closed the timer will count down to zero and close the relay again, if the door is re-opened before the timer has expired then the timer will start over, the delay is set using J 1, 2 & 3.
|
|
|
Flip Delay Flop/DK
0 kg
Spec Sheet
|
Flip Delay Flop Module
The FDF Module is a compact control PCB that will trigger when the NC input is closed with a push to close button or momentary input, when this occurs the FDF Module will trigger the relay contacts at this point a timer will hold the relay active disabling the input, and hold this state until the preset time has expired, then the momentary input / button is pushed again to toggle the relay off.
|
|
|
Delay Start Module/DK
0 kg
Spec Sheet
|
Delay Start Module
The Delay Start Module is a small compact PCB that on removal of the NC loop will start an adjustable delay time. At the end of this delay a 1A relay will energise a set of contacts. The relay will only de-energise when the NC loop has been restored. The timer is software driven and is available in 1-8 5-40 10-80 seconds, see the spec sheet for full details. The timer can also be triggered from a -VE input, or by leaving the loop open and applying power to the PCB and the timer will start on power up. Other delay times may also be available upon request.
When ordering please contact sales office for software version.
|
|
|
